Showing all Ducting Raceway
Part Number: TC1279-750KIT
This kit is installed from the front to the rear of a data rack, allowing fibre cords to be fed from front to back of the rack. The duct is supported by two sturdy metal mounting brackets fitted to the front and rear equipment mounting rails on either the left or right hand side; (4 x mounting screws and cage nuts are supplied). This kit occupies 2 RU of mounting space. The mounting brackets hold duct securing (“C”) brackets, which have 65mm of lateral adjustment. A length of 100mm x 50 mm duct carries the cords. It is supplied as a length of 800mm, which can be trimmed to suit the depth of the data rack. One end of the duct is slotted to accept a trumpet secured by a standard joiner. The other, (non-slotted), duct end is accurately cut to length and a trumpet is secured to the cut end of the duct using a slotless joiner.
Part Number: TC1279-536KIT
This 1RU kit is installed from the front to the rear of an equipment rack, allowing fibre cords to be fed from front to back of the rack. The duct is supported by two sturdy metal mounting brackets fitted to the front and rear equipment mounting rails (4 x mounting screws and cage nuts are supplied). The mounting brackets hold duct securing (“C”) brackets, which have a little adjustment. A short length of 30mm x 30mm duct carries the cords. One end of the duct is slotted to accept a 900 down elbow, secured by a standard joiner. The other slotted duct end accepts a 90o horizontal LH or RH elbow.
Part Number: PGTC1279-751KIT
The Duct Kit fits to a 1 metre deep Equipment Rack, and enables optical fibre cords to be fed from the front to rear of rack, either LHS or RHS. Mounting brackets and screws provided
Part Number: TC1279-434
This 90o Elbow is typically used to feed an optical fibre cable into a cabinet, after the cable has “broken-out” into several optical fibres. The Elbow is fastened to the cabinet using an M50 nut, after passing through a clearance hole. The lower end of the Elbow can accept either a 38mm dia cable ; or a Convoluted Tube, which houses the incoming optical fibre cable. The inner radius of the Elbow is 56mm, and the internal diameter is 41.5mm; so the Elbow can typically accept a cable of around 37/38mm dia
Part Number: TC1279-307S-2
A pair of plastic mounting clips, enables an “Over the Top Outlet” to be located anywhere along a metal duct run. This enables optical fibre cords to leave the duct run at any position along its length, whilst maintaining the MBR at 30mm. The “Over the Top Outlet” allows 2.0mm dia optical fibre cords to “drop-off” the duct run and feed into 100mm x 100mm (FR) plastic duct and components. The “Over the Top Outlet” is Part No: TC1279-307A; and is available separately.
WBTs YellowDuct straight ducting~raceway is available in six sizes with or without covers. Slotted duct/raceway is available in some sizes for vertical drops or applications inside equipment racks to allow cords to exit through the side of the duct. Some sizes are available with hinged covers (hinges included in pack), or clip on covers. All duct sizes come in 2m (6.3′) lengths, and where required, are slotted at each end for simply snapping together with an appropriate joiner. Most other ducting – raceway brands are only available in 6 foot lengths – 10% shorter than Lightpaths.
WBT YellowDuct joiners are used to snap together system components and straight ducting~raceway. They simply snap into the slots in the end of each piece to be joined.
The YellowDuct ducting raceway system has 2 option methods for joining the components together, slotted joiners or slotless joiners:
- Slotted Joiners require the ducting components to have slots on the ends so that it can be properly joined by clicking into place. A slotting tool will be required.
- Slotless joiners require no additional tooling or for slots to be made in the side of the
duct. They only require a screwdriver for installation to tighten the joiner into place
Note: For straight ducting~raceway that has been cut to length, new slots need to be made with a suitable size slotting tool.
WBT YellowDuct vertical elbows are used to connect horizontal routes at different height, or to allow the fiber path to be raised or lowered to avoid obstacles. Retrofit versions are used where there is existing fiber. They are available with or without covers.
WBT YellowDuct Tubing is used for feeding entering or exiting fibers from the ducting~raceway into equipment racks. They are convoluted or ribbed to allow adjustment if drops cannot be positioned exactly over or under equipment. Some are available with removable covers, or split for ease of cable installation.
These components provide different methods of allowing fibres to enter or leave the duct – raceway. They can be purchased as kits or as individual items.
Duct Side Drop-off Installation
Express Top Outlet drop-off to Ducting Installation
Side Drop Off to 50mm Ducting Raceway via Convoluted Tubing
These new Duct breakout kits provide the ideal solution for a high capacity fibre cord outlet. This solution provides a safe and effective means of protecting optic fiber cords and allows for easy routing of cords down into a Telecommunications frame. Duct outlets can be placed anywhere along the duct and minimal time and effort is required to install these outlet components. This solution allows for quickest installation as less cuts are required and is also stronger as the ribs of duct are not cut.